Raspberry Pi and SBCS, Tutorials and Walkthroughs

How to Install a Raspberry Pi 5 in the Argon ONE V3 NVMe Case

Learn how to install a Raspberry Pi 5 in the Argon ONE V3 NVMe case, boot Raspberry Pi OS from an M.2 drive, and see how cool the case keeps it under load.

Mackey Tech video thumbnail: The Ultimate Raspberry Pi 5 Case (NVMe + Cooling!)

Watch the video on YouTube

This guide walks through installing a Raspberry Pi 5 into the Argon ONE V3 M.2 NVMe case, adding an M.2 NVMe drive, and booting Raspberry Pi OS straight from that drive. I also set up the case’s fan and power button scripts and checked how warm the Pi gets under load.

What Comes in the Argon ONE V3 Box

The Argon ONE V3 is one of the most popular Raspberry Pi 5 cases, and it’s easy to see why. It gives you full size HDMI ports and built in support for NVMe storage. Inside the box you get the case, an instruction manual, an HDMI and power board, and a bag of accessories with two PCIe cables (one is a spare), heat sinks, feet pads and mounting screws.

The top half of the case holds the fan, the female GPIO header and two mounting spots for the heat sinks. The case is magnetic, so if you lose a screw, check the case first, because it has probably stuck itself to the top or bottom. Under the magnetic cover you’ll also find a handy GPIO pin layout for the Pi 5.

Jumpers on the board control how the power button behaves. By default, you press the power button to turn the Pi on. If you switch the jumpers to always on, the Pi boots the moment you plug in power. I left them at the default so the power button stays in charge.

Around the back you’ll find USB C, a 3.5 mm audio jack, two full size HDMI ports, the power button, and cutouts for Ethernet and USB. The bottom half has two pogo pins, the PCIe connection and a compartment for the NVMe drive.

One thing the box doesn’t include is a power supply. Any USB C supply that works with the Raspberry Pi 5 should do the job, as long as it delivers 5.1 volts at 5 amps.

Assembling the Raspberry Pi 5 in the Argon ONE V3

Start with the HDMI and power board. The single connector goes into the Pi’s USB C port and the other two go into the micro HDMI ports, with the full size HDMI ports facing the Ethernet and USB side. It doesn’t take much force, but you want it snug, so flip the Pi over and check that everything lines up.

Next comes the PCIe cable. Use your fingernail to gently lift the latch on the Pi’s PCIe connector, slide the cable in with the copper side facing up, and press the latch closed. The copper side has to face the right way, because those are the contacts that carry the connection to your drive.

Now drape the cable over the top and seat the Pi into the top half of the case, lining up the GPIO pins with the female header. When everything lines up, the board slides in smoothly and the ports sit right in their cutouts. Put the heat sinks on before this step! I forgot them on my first pass and had to go back.

Flip the case onto its back and connect the other end of the PCIe cable to the bottom half the same way, with the copper side showing. Then screw the Pi board down to the case.

Why the Pogo Pins Matter

Before you close things up, take a look at the two pogo pins on the bottom section. One carries 5 volts and the other is ground, and they line up with matching contact points on the other half of the case. They have to touch for the power button and the NVMe drive to work, so keep them in mind as you position the bottom half. Then secure it with the screws.

Picking an NVMe Drive the Argon ONE V3 Will Boot From

This is where I hit a snag. My first drive was a spare 256 GB HP EX900 Plus, which isn’t on Argon’s compatibility list. Instead of booting, it kept dropping me to a BusyBox prompt, which means the system couldn’t find or mount the root file system on the NVMe drive.

I tried resetting the drive, reflashing the OS and changing the bootloader configuration. I also checked the bootloader EEPROM, which needs firmware from December 6, 2023 or later to boot from NVMe, and mine was already up to date. At that point, the drive itself was clearly the problem.

So I overnighted a 256 GB Western Digital SN740, which is on Argon’s list. It’s a shorter 2242 drive instead of the HP’s 2280 length. I flashed Raspberry Pi OS onto it, swapped it in, and it booted right up! If you’re buying a drive for this case, why not check Argon’s compatibility list first? It could save you an evening of troubleshooting.

Installing the NVMe Drive in the Argon ONE V3

Remove the screws on the NVMe compartment. The case comes with a heat sink sized for 2280 drives, which was too big for my 2242, so I used a different one I had on hand. If you use a 2242 drive, move the standoff from the 2280 position down to the shorter 2242 position before you screw the drive in.

Booting Raspberry Pi OS From NVMe

Plug in HDMI, USB C power, and a keyboard and mouse. The first boot was quick, and it landed in the 64 bit version of Raspberry Pi OS. To confirm the Pi is actually running from the NVMe drive, open a terminal and list the block devices:

lsblk
lsblk
lsblk

You should see the NVMe drive along with its boot partition. To check which version of Raspberry Pi OS you’re running:

lsb_release -a
lsb_release -a
lsb_release -a

Mine came back as Trixie.

Setting Up the Argon ONE V3 Fan and Power Button

Next, install the scripts from Argon’s manual. My Pi was already booting from the NVMe drive without them, so you don’t need them for that. The first script tunes the EEPROM settings for the case’s power supply and the NVMe drive, and the second sets up the power button and fan control. Reboot after each one.

curl https://download.argon40.com/argon-eeprom.sh | bash
sudo reboot
curl https://download.argon40.com/argon-eeprom.sh | bash
sudo reboot
curl https://download.argon40.com/argon-eeprom.sh | bash
sudo reboot
sudo apt-get update
sudo apt-get full-upgrade -y
curl https://download.argon40.com/argon1.sh | bash
sudo reboot
sudo apt-get update
sudo apt-get full-upgrade -y
curl https://download.argon40.com/argon1.sh | bash
sudo reboot
sudo apt-get update
sudo apt-get full-upgrade -y
curl https://download.argon40.com/argon1.sh | bash
sudo reboot

How Cool Does the Argon ONE V3 Keep the Pi 5?

According to the manual, the fan kicks on at 30% once the CPU passes 55°C, jumps to 55% at 60°C and runs at 100% at 65°C.

To test it, I ran a five minute stress test while playing a YouTube video at 1440p. The CPU stayed around 51°C, so the fan never even turned on. With the video in full screen and the stress test running again, the temperature only reached about 53°C. The video dropped a few frames here and there, but overall the Pi held up well.

Under these moderate workloads the fan never needed to kick in, so the whole setup stayed dead quiet.

Is the Argon ONE V3 Worth It for Your Pi 5?

You end up with a Raspberry Pi 5 tucked into a compact case with full size HDMI, booting from a fast NVMe drive and staying quiet under moderate loads. I like this case because it’s small, efficient and easy to use. The one lesson I’d pass along is to stick with a drive from Argon’s compatibility list. What case are you using for your Pi 5?

Argon’s full manual, including the fan and power button scripts: Argon ONE V3 Instruction Manual

💻 Hardware I Used: ✅ Some links may be affiliate links, which help support me and help keep ads off here!

  1. Argon ONE V3 M.2 NVMe Case: https://amzn.to/3X5wThA

  2. Raspberry Pi 5 16GB: https://amzn.to/4qBRo2X

  3. WD SN740 256GB M.2 NVMe: https://amzn.to/4nCvvxU

  4. Raspberry Pi 5 Power Supply: https://amzn.to/4qDnprr

  5. Fanttik Screwdriver Set: https://a.co/d/0gSsjEIR

MACKEY TECH

Making Technology Accessible for Everyone

Connect

© 2026 Mackey Tech. Homelabs, Linux, NAS and practical tech tutorials.